#How to make photo frame from cardboard how to#
#How to make photo frame from cardboard plus#

Here at Frame It Easy, we use acid-free foamcore in our frames, which is meant to combat harmful acids found in the paper your photos and art are printed on. One thing specifically to avoid in frames, however, is cardboard. That said, there are things you can put into frames that can preserve them for as long as possible. Indeed, even the most priceless of paintings, undoubtedly maintained under strict protocols, can fade. Of course, itвЂ™s impossible to totally stop the passage of time from showing on our favorite photos and art. This means you want it looking its best, and you want to minimize the possibility of external forces degrading it.

I used a вЂњselfВ levelingвЂќ picture hanger to hold my frame up to the wall.If you have a picture that you want to be framed, it probably means you want it displayed on your wall for years to come.

These allows you to change the picture, clean the glass etc and then put everything back. The screws mine came with were too long, so I had to use shorter.

Cut a piece of cardboard to work as the backer for the whole thing.My staples went through the narrowВ moldingВ a little bit into the wideВ moldingВ without going all the way through (1/2 inch staples) Use the staple gun to staple across the joints. This leaves an inset area in the middle for the glass and backing to rest. Glue the narrower molding pieces to the edge of the wide frame.I did this the reverse way on mine, but I think this way is better. I just held it up to the glued wider frame and marked it. The long pieces will be the same as they were for the wide molding, but your top and bottom pieces will have to make up the difference in thickness. In addition to the wider molding вЂ“ weвЂ™re going to use a narrower piece on top.Glue edge to edge in the formation shown in the diagram and in the photo below.Sand all edges a bit to make sure they look polished. Cut your wide molding to length using the miter box and hand saw.

#How to make photo frame from cardboard plus#

The side pieces are the length of the image PLUS the thickness of the top pieces. The way weвЂ™re going to be doing it, the top pieces are as long as you image is wide.

First of all, calculate the WIDER molding.

Glass or plexi (I hear Lowes will cut the glass you buy there.

Screws, if those with your Turn Buttons are too long.

Turn buttons (You might find these near the glass section at your hardware store.

Heavy duty stapler and 1/2 inch staples.

Also, if you are so inclined, you can make 45 degree angles on the corners with this)

Hand saw and miter box (This helped me cut straight.

I wasnвЂ™t able to find any, so I improvised! What You Need: I know there is such a thing as picture molding, that has that routered groove built in. The basicВ premiseВ is to stack molding toВ substituteВ the routered groove that the back of most frames have. I KNOW I will be using this little trickВ again! And thereвЂ™s a bonus В some of the screws and such I bought are left over, and I can make another frame if I just get more molding and glass. Really, making my own DIY picture frame was SO easy and actually cheaper than buying a frame at a department store.

#How to make photo frame from cardboard how to#

Recently,В I resolved to figure out how to build a picture frame for that lovely print, and IвЂ™m so glad I did! As a result I was able to build a picture frame that showcases my lovely print. ItвЂ™s a strange size and since I wasnвЂ™t going to have it custom framed for a small fortune, it has been sequestered to a box in a closet. IвЂ™ve had this beautiful art print for years that I just havenвЂ™t been able to find a frame for (I blurred bits of it for copyright stuff). Some are square, some are wide and squat, some are tall and skinny. Heck, not all of them are a proportional rectangle. Not every pretty thing fits in an 8Г—10 frame.